Custom o ring factory in China? DMS Custom Rubber Rings, O Ring Company & factory covers an area of more than 10,000 square meters and the factory area is 8,000 square meters. Our production equipment and test equipment are at the leading level in the industry. We are one of the largest companies in China specializing in the production and development of seals. We have long-term communication and cooperation with many universities and research institutions at home and abroad. Discover additional details at ptfe seals manufacturer.
It is ideal for single-acting sealing of reciprocating piston rods or pistons with a wide operating pressure range of up to 20 MPa. The operating temperature range is also wide from -200°C to + 250°C. It has a diameters range from 3 mm to 1600 mm and a working speed of 5 m/s. The seal has a low coefficient of friction and the friction between the contact faces is minimal among all seal types. Moreover, the contact pressure between the mating surfaces is low. It can work without lubrication and is very wear resistant. And it has a long service life.
The gasket made by DMS SEALS is uniquely mechanical and thermally stable and it has excellent oxidation resistance. Compared with other thermoplastics, it can be applied to components such as valves and bushings, with higher wear resistance, higher mechanical properties and thermal fatigue resistance. At the same time, it has excellent oil resistance (alkane oil), heat resistance, water resistance, aging resistance, air tightness and excellent adhesion. It is commonly used in media such as water, oil, and natural gas.
Our piston seals are designed to provide excellent leak control. We guarantee that it can perfectly meet the user’s requirements for low friction, compactness, precise configuration and simple installation. It is designed for fluid power applications. It is made of compound materials with high performance, which guarantees excellent wear resistance and excellent extrusion resistance for the seal. It is designed to be suitable for almost all fluid media and is highly resistant to oxidation and corrosion. It has excellent dynamic and static sealing performance and can even work under dusty industrial environments. Moreover, it has strong adaptability to various working conditions and can adapt to a fast, high-pressure working environment. At the same time, it has unparalleled performance in extreme temperature environments.
Influence of flange form: Different flange forms require different gaskets. Smooth-faced flanges are generally only used for low pressure, with soft thin gaskets; under high pressure, if the strength of the flange is sufficient, smooth-faced flanges can also be used, but thick soft gaskets should be used, or inner belt reinforcement should be used. Wound gasket for ring or reinforcement ring. In this case, metal gaskets are also not suitable, because the required pressing force is too large, resulting in large deformation of the bolts, making the flange difficult to seal. If a metal gasket is to be used, the smooth surface should be reduced to reduce the contact area with the gasket. In this way, under the condition of the same bolt tension, the compressive stress of the reduced narrow smooth surface will increase.
Due to the volume and weight limitations of the system, it is impossible to install an ideal filtration and cooling system. High temperature, high pressure, and high speed cause the hydraulic oil to deteriorate easily, and the mechanical parts are also prone to erosion and stains. There are many stains and impurities in hydraulic oil, but it cannot be thoroughly filtered, which is the aspect of endogenous stains. All kinds of dust in the working environment may be very large, and it will inevitably enter the hydraulic system in multiple ways, causing oil pollution, which is an external stain. Therefore, the sealing system is required to be resistant to stains.
Support and positioning The piston and piston rod are radially supported and positioned in the cylinder barrel. Isolate the two pairs of motion pairs of piston and cylinder, piston rod and guide sleeve to prevent direct scratches, abrasions and strains between the motion pairs. Especially when the motion pairs are all steel parts, they must be isolated, otherwise they will be easily strained. The guide belt also has an important role to reduce the friction and friction work between the moving parts, reduce the ineffective work and heat. Vibration absorption and noise reduction Reduce system vibration and noise. It is mainly filled with tetrafluoroethylene and phenolic cloth, and there are also a very small amount of polyoxymethylene, nylon and soft metal. Read more information on dmsseals.com.