Top hydraulic seals manufacturer: Types of Mechanical Seals – Several types of mechanical seals are available. Some of the popular ones include: Balanced and unbalanced seals; Pusher and non-pusher seals Cartridge seals. A mechanical seal consists of rotary and stationary faces running against each other. These faces apply a closing force against each other using springs and the pressure generated from the process fluid. This way, a seal is formed to prevent the fluid from leaking between the rotating shaft and the pump housing. Mechanical seals can be selected based on the type of pump application. Choosing the wrong seal can affect pump performance and lead to damage and costly repairs. An unbalanced mechanical seal is preferred if the pump needs to operate at a lower pressure. However, high pressure pumping applications require balanced mechanical seals. Balanced seals also perform better in high temperature operating conditions. Cartridge seals require less maintenance but are more expensive, hence used for limited applications. Find even more information at https://www.dmsseals.com/scraper-seals.
The Fluid Film – In most mechanical seals the faces are kept lubricated by maintaining a thin film of fluid between the seal faces. This film can either come from the process fluid being pumped or from an external source. The need for a fluid film between the faces presents a design challenge – allowing sufficient lubricant to flow between the seal faces without the seal leaking an unacceptable amount of process fluid, or allowing contaminants in between the faces that could damage the seal itself. This is achieved by maintaining a precise gap between the faces that is large enough to allow in a small amounts of clean lubricating liquid but small enough to prevent contaminants from entering the gap between the seal faces. This micro-gap is maintained using springs and hydraulic force to push the seal faces together, while the pressure of the liquid between the faces (the fluid film) acts to push them apart.
The gasket made by DMS SEALS is uniquely mechanical and thermally stable and it has excellent oxidation resistance. Compared with other thermoplastics, it can be applied to components such as valves and bushings, with higher wear resistance, higher mechanical properties and thermal fatigue resistance. At the same time, it has excellent oil resistance (alkane oil), heat resistance, water resistance, aging resistance, air tightness and excellent adhesion. It is commonly used in media such as water, oil, and natural gas.
Scraper seals are also known as wiper seals. The scraper sealof DMS SEALS can effectively prevent various forms of contamination that cause a hydraulic system failure. It can be mounted on the outside of the piston rod seal of the hydraulic cylinder to protect the hydraulic cylinder from dirt, dust and moisture. It can well protect the hydraulic cylinder from environmental pollution and effectively prevent damage to the hydraulic cylinder parts, causing the system to malfunction. DMS offers a wide range of wiper seals for different hydraulic systems with different characteristics, specifications and combinations.
Gasket sealing mechanism: The function of the gasket is caused by the blocking effect on the internal medium formed by the contact pressure of the sealing material on the joint surface and the elastic restoring force to the external tightening force. Classification and structure of gaskets: Gaskets are divided into three categories: non-metallic gaskets, non-metallic and metal combined gaskets and metal gaskets. The common materials are rubber, leather, asbestos board, cork, PTFE, tinplate, steel, aluminum, copper and stainless steel.
Support and positioning The piston and piston rod are radially supported and positioned in the cylinder barrel. Isolate the two pairs of motion pairs of piston and cylinder, piston rod and guide sleeve to prevent direct scratches, abrasions and strains between the motion pairs. Especially when the motion pairs are all steel parts, they must be isolated, otherwise they will be easily strained. The guide belt also has an important role to reduce the friction and friction work between the moving parts, reduce the ineffective work and heat. Vibration absorption and noise reduction Reduce system vibration and noise. It is mainly filled with tetrafluoroethylene and phenolic cloth, and there are also a very small amount of polyoxymethylene, nylon and soft metal. Discover additional information on dmsseals.com.
DMS Seals is a scientific and technical mechanical seal manufacturer and oil seal supplier specializing in seal production, sealing material development, and the conception of sealing solutions for special working conditions. We have 120 employees, including 70 senior technicians. DMS Seals has a number of invention patents and leading production processes. The R&D team is able to design and develop Rubber Seal & Hydraulic Seals for various mechanical sealing systems under complex conditions. We have already passed the certification of ISO 9001 and TS 16949.
Because the system pressure is high, the temperature is high, and the wear is particularly serious, the seal is required to have good wear resistance. Low coefficient of friction: For construction machinery such as excavators and pump trucks, the hydraulic system pressure is high, the cylinder action speed is fast, and the wear of the seal is particularly serious. Therefore, the friction coefficient of the seal must be low, so that the seal has good wear resistance and suitable life.
The radial force of our rotary seals on the shaft and the distribution is very reasonable. It can achieve the optimal “critical oil film thickness” working condition and always maintain critical lubrication. We guarantee that our rotary seal can help the machine get the sharpest “peak” pressure distribution with the least radial force, providing the best sealing effect. The bearing seal is designed by DMS SEALS to isolate the moving metal part, guiding the piston and piston rod of the hydraulic cylinder to move in a certain direction and it can help withstand lateral loads. It helps prevent any direct contact between the piston metal and the cylinder metal and prevents strain and seal damage on the inner surface of the cylinder.